![]() ![]() : adding the kerberos master key to the directory #Install git lfs on amazon ec2 vm password: adding the password extension to the directory : configuring directory to start on bootĬonfiguring Kerberos KDC: Estimated time 30 seconds ![]() Restarting IPA to initialize updates before performing deletes: : configure new location for managed entries ![]() : Configure HTTP to proxy connectionsĬonfiguring directory server: Estimated time 1 minute : configuring certificate server to start on boot : importing CA chain to RA certificate database : creating CA agent PKCS#12 file in /root : configuring certificate server instance : creating directory server instanceĬonfiguring certificate server: Estimated time 3 minutes 30 seconds Please wait until the prompt is returned.Ĭonfiguring directory server for the CA: Estimated time 30 seconds The following operations may take some minutes to complete. Using reverse zone 66.111.10.in-addr.arpa. Please provide a realm name :ĭo you want to configure DNS forwarders? :Įnter the IP address of DNS forwarder to use, or press Enter to finish.Įnter IP address for a DNS forwarder: 172.16.0.23ĭo you want to configure the reverse zone? : This is typically the domain name converted to uppercase. The kerberos protocol requires a Realm name to be defined. The IPA Master Server will be configured with The domain name has been calculated based on the host name. Warning: skipping DNS resolution of host On which you're setting up server software. To accept the default shown in brackets, press the Enter key.Įxisting BIND configuration detected, overwrite? : yĮnter the fully qualified domain name of the computer * Create and configure a Kerberos Key Distribution Center (KDC) * Create and configure an instance of Directory Server * Configure the Network Time Daemon (ntpd) * Configure a stand-alone CA (dogtag) for certificate management The log file for this installation can be found in /var/log/ipaserver-install.log dpal: yes that would also be an appropriate fallback To fallback to ldappasswd if kpasswd changes fail if we need to support that we may want a ticket in sssd to try However you can always use ldappasswd to perform password changes Side so pwd changes from the outside netowkr using kpasswd may fail If the fix is needed only on the server side or also on the client I think MIT fixed them over NAT only in 1.11 and I am not sure The only exception I think may be password cahnges Of course I am not putting my hand on fire wrt SRV recordsīut in general the problem would be mostly confined to DNS views if the client outside can resolve name -> public-ip it We do not support views in IPA though I think I've seen a Private IP while clients outside it see the public IP With views so that clients on your private LAN see the dpal: the name itself can be usable from the outsideīut you may have to set up your own DNS server and play Location so may really need to route stuff around and I guess people may have distributed resources in multiple Would be desirable but that's not up to me so I would think actually just using private IPs only #Install git lfs on amazon ec2 vm installin general though I do not think you want to install But do you think this name will be usable form the outside? of course then you may have issues with kerberos if DNS dpal: just add in /etc/hosts private-ip desired-hostname the IP itslef is not a real issue, unless you try to set dpal: ok the point is that you can set whatever hostname And I suspect this is where the install would not work ip-address=internal-ip but then it uses the internal TX packets:12170 errors:0 dropped:0 overruns:0 carrier:0 RX packets:44356 errors:0 dropped:0 overruns:0 frame:0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Ipa-server-install: error: option -ip-address: invalid IP addressĥ0.19.212.236: No network interface matches the provided IP address and ~]# ifconfig eth0Įth0 Link encap:Ethernet HWaddr 12:31:3B:02:5C:3D No network interface matches the provided IP address and ~]# ipa-server-install -ip-address=50.19.212.236 Unexpected error - see ipaserver-install.log for details: The specific issue even occurs when trying to force the IP address that the The public facing IP will never match up with the address of the interface,Įven to other machines which will be accessing IPA. Situated behind network address translation. On Amazon EC2 virtual machines are provisioned with an IP address effectively Due to checks in the installer related to IP addressing, IPA will not install ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |